Slic3r config 12-27-16

From MakeICT Wiki
Jump to navigationJump to search
# generated by Slic3r 1.2.9 on Tue Dec 27 17:58:15 2016

[filament:RepRap Ninjaflex]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 210

[filament:RepRap PLA]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 200

[filament:Rostock ABS]
bed_temperature = 80
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 30
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 225
max_fan_speed = 100
min_fan_speed = 41
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 220

[filament:Rostock PLA]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 210

[filament:Rostock PLA - Wood]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 200

[filament:Ultimaker ABS]
bed_temperature = 80
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 0.93
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FF1100
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 240
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 240

[filament:Ultimaker PLA]
bed_temperature = 60
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 3
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF1100
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 5
temperature = 210

[presets]
filament = Ultimaker PLA.ini
print = Ultimaker 2.ini
printer = Ultimaker 2.ini

[print:RepRap]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.25
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 20
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 5
travel_speed = 80
xy_size_compensation = 0

[print:RepRap-James]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 45
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.35
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.35
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.2
first_layer_speed = 15
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.35
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 45
interface_shells = 0
layer_height = 0.1
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 20
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.35
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 15
solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.35
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 45
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0.35
top_solid_infill_speed = 15
top_solid_layers = 5
travel_speed = 80
xy_size_compensation = 0

[print:RepRap.old]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.25
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 30
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 5
travel_speed = 80
xy_size_compensation = 0

[print:Rostock]
avoid_crossing_perimeters = 1
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 45
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 15
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 20
infill_speed = 40
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 25
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 0
thin_walls = 1
threads = 5
top_infill_extrusion_width = 0
top_solid_infill_speed = 30
top_solid_layers = 4
travel_speed = 150
xy_size_compensation = 0

[print:Ultimaker 2]
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 45
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.4
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 110%
first_layer_height = 0.2
first_layer_speed = 15
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 20
infill_speed = 45
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 10
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 30
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 2
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.4
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 30
top_solid_layers = 5
travel_speed = 150
xy_size_compensation = 0

[print:Wood]
avoid_crossing_perimeters = 1
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 2
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 25%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 15
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 20
infill_speed = 80
interface_shells = 0
layer_height = 0.2
max_print_speed = 70
max_volumetric_speed = 0
min_skirt_length = 25
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 5
top_infill_extrusion_width = 0
top_solid_infill_speed = 80%
top_solid_layers = 4
travel_speed = 150
xy_size_compensation = 0

[printer:Reprap]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nG1 \nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.35
octoprint_apikey = E2758749A97D42DFAD2F2F2480ACFAF3
octoprint_host = 192.168.9.119
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\n;Next line shouldn't be needed.\n;G92 Z109; Correct Z, since we home at Zmax\nG1 Z5 F150 ;bring the nozzle down to just off the bed. \n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:Reprap-James]
bed_shape = 0x0,160x0,160x160,0x160
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nG1 \nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.35
octoprint_apikey = E2758749A97D42DFAD2F2F2480ACFAF3
octoprint_host = 192.168.9.119
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\n;Next line shouldn't be needed.\n;G92 Z109; Correct Z, since we home at Zmax\nG1 Z5 F150 ;bring the nozzle down to just off the bed. \n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:Rostock]
bed_shape = 129.288x13.5887,127.159x27.0285,123.637x40.1722,118.761x52.8758,112.583x65,105.172x76.4121,96.6088x86.987,86.987x96.6088,76.4121x105.172,65x112.583,52.8758x118.761,40.1722x123.637,27.0285x127.159,13.5887x129.288,0x130,-13.5887x129.288,-27.0285x127.159,-40.1722x123.637,-52.8758x118.761,-65x112.583,-76.4121x105.172,-86.987x96.6088,-96.6088x86.987,-105.172x76.4121,-112.583x65,-118.761x52.8758,-123.637x40.1722,-127.159x27.0285,-129.288x13.5887,-130x0,-129.288x-13.5887,-127.159x-27.0285,-123.637x-40.1722,-118.761x-52.8758,-112.583x-65,-105.172x-76.4121,-96.6088x-86.987,-86.987x-96.6088,-76.4121x-105.172,-65x-112.583,-52.8758x-118.761,-40.1722x-123.637,-27.0285x-127.159,-13.5887x-129.288,0x-130,13.5887x-129.288,27.0285x-127.159,40.1722x-123.637,52.8758x-118.761,65x-112.583,76.4121x-105.172,86.987x-96.6088,96.6088x-86.987,105.172x-76.4121,112.583x-65,118.761x-52.8758,123.637x-40.1722,127.159x-27.0285,129.288x-13.5887,130x0
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG91\nG1 Z10 E-5.0 F12000\nG90\nG28 \nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
octoprint_apikey = 1589B335DF114E36B8EC3B48EF13A167
octoprint_host = 192.168.9.111:80
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 4
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0.1
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = M104 S[temperature]\n\nM190 S[bed_temperature]\n\nM109 S[temperature]\n\nG28
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[printer:Rostock - Wood]
bed_shape = 129.288x13.5887,127.159x27.0285,123.637x40.1722,118.761x52.8758,112.583x65,105.172x76.4121,96.6088x86.987,86.987x96.6088,76.4121x105.172,65x112.583,52.8758x118.761,40.1722x123.637,27.0285x127.159,13.5887x129.288,0x130,-13.5887x129.288,-27.0285x127.159,-40.1722x123.637,-52.8758x118.761,-65x112.583,-76.4121x105.172,-86.987x96.6088,-96.6088x86.987,-105.172x76.4121,-112.583x65,-118.761x52.8758,-123.637x40.1722,-127.159x27.0285,-129.288x13.5887,-130x0,-129.288x-13.5887,-127.159x-27.0285,-123.637x-40.1722,-118.761x-52.8758,-112.583x-65,-105.172x-76.4121,-96.6088x-86.987,-86.987x-96.6088,-76.4121x-105.172,-65x-112.583,-52.8758x-118.761,-40.1722x-123.637,-27.0285x-127.159,-13.5887x-129.288,0x-130,13.5887x-129.288,27.0285x-127.159,40.1722x-123.637,52.8758x-118.761,65x-112.583,76.4121x-105.172,86.987x-96.6088,96.6088x-86.987,105.172x-76.4121,112.583x-65,118.761x-52.8758,123.637x-40.1722,127.159x-27.0285,129.288x-13.5887,130x0
before_layer_gcode = 
end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG91\nG1 Z10 E-5.0 F12000\nG90\nG28 \nM84     ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.5
octoprint_apikey = 1589B335DF114E36B8EC3B48EF13A167
octoprint_host = 192.168.9.111:80
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 7
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 95
start_gcode = M104 S[temperature]\n\nM190 S[bed_temperature]\n\nM109 S[temperature]\n\nG28
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[printer:Ultimaker 2]
bed_shape = 0x0,223x0,223x223,0x223
before_layer_gcode = 
end_gcode = G28  ; home all\nM104 S0 ; turn off heaters\nM140 S0 ; turn off bed\nM84 ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 672B8BCE1CD6427E8CD9CE77E9D52B51
octoprint_host = 192.168.9.112
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 5
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes\nG1 X110 Y45 F3000 ; bring extruder to the front\nG92 E0 ; zero the extruded length\nG1 Z30 ; lower\nG1 E50 F225 ; purge nozzle with 50mm of filament\nG1 X80 Y60 F3000 ; move aside of the puddle of primed plastic\nG92 E0 ; zero the extruded length again
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[printer:Ultimaker 2-test]
bed_shape = 0x0,223x0,223x223,0x223
before_layer_gcode = 
end_gcode = G91 ; relative coordinates  \nG1 Z0.2 ; retract lift  \nG1 E-20 F3000 ; reverse priming  \nG90 ; absolute coordinates  \nG28 ; home all axes  \nM104 S0 ; turn off extruder heaters  \nM140 S0 ; turn off bed heater  \nM84 ; disable motors  
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 672B8BCE1CD6427E8CD9CE77E9D52B51
octoprint_host = 192.168.9.112
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 4.5
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = G28 ; home all axes  \nG1 F12000 X5 Y10 ; Cura HEATUP_POSITION_COMMAND  \nM190 S[first_layer_bed_temperature] ; wait for bed temperature to be reached  \nM109 S[first_layer_temperature] ; wait for temperature to be reached  \nG1 F2400 Z20 ; bring plate to Cura PRIMING_HEIGTH with Cura HOMING_FEEDRATE  \nG92 E0 ; zero the extruded length  \nG1 F500 E20 ; undo end of print/abort retraction  \nG92 E0 ; zero the extruded length  \n;G1 F50 E5 ; additional priming   ; not neccessary\nG1 F2400 X20 Y20 Z0.3 ; wipe start position  \nG92 E0 ; zero the extruded length  \nG1 F225 X35 E2 ; move 15mm and extrude  \nG92 E0 ; zero the extruded length  \nG1 F2100 X50 E1 ; move 15mm  \nG92 E0 ; zero the extruded length  
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[settings]
autocenter = 1
mode = expert

[simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,180x0,180x180,0x180
bed_temperature = 0
before_layer_gcode = 
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 30
first_layer_temperature = 205
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_gcode = 
layer_height = 0.25
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.35
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 5
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 200
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0